Difference between revisions of "G-Code"
From CNC.xyz Wiki
(Redirected page to wikipedia:G-code) |
|||
| Line 1: | Line 1: | ||
| − | + | {| class="wikitable" | |
| + | |- | ||
| + | ! Header text !! Header text | ||
| + | |- | ||
| + | | [[G0]] || Coordinated Straight Motion Rapid Rate | ||
| + | |- | ||
| + | | [[G1]] || Coordinated Straight Motion Feed Rate | ||
| + | |- | ||
| + | | [[G2 G3]] || Coordinated Helical Motion Feed Rate | ||
| + | |- | ||
| + | | [[G4]] || Dwell | ||
| + | |- | ||
| + | | [[G5.1]] || Quadratic B-Spline | ||
| + | |- | ||
| + | | [[G5.2 G5.3]] || NURBs Block | ||
| + | |- | ||
| + | | [[G7]] || Diameter Mode (lathe) | ||
| + | |- | ||
| + | | [[G8]] || Radius Mode (lathe) | ||
| + | |- | ||
| + | | [[G10 L1]] || Set Tool Table Entry | ||
| + | |- | ||
| + | | [[G10 L10]] || Set Tool Table, Calculated, Workpiece | ||
| + | |- | ||
| + | | [[G10 L11]] || Set Tool Table, Calculated, Fixture | ||
| + | |- | ||
| + | | [[G10 L2]] || Coordinate System Origin Setting | ||
| + | |- | ||
| + | | [[G10 L20]] || Coordinate System Origin Setting Calculated | ||
| + | |- | ||
| + | | [[G17]] - [[G19.1]] || Plane Select | ||
| + | |- | ||
| + | | [[G20 G21]] || Units of Measure | ||
| + | |- | ||
| + | | [[G28]] - [[G28.1]] || Go to Predefined Position | ||
| + | |- | ||
| + | | [[G30]] - [[G30.1]] || Go to Predefined Position | ||
| + | |- | ||
| + | | [[G33]] || Spindle Synchronized Motion | ||
| + | |- | ||
| + | | [[G33.1]] || Rigid Tapping | ||
| + | |- | ||
| + | | [[G38.2]] - [[G38.5]] || Probing | ||
| + | |- | ||
| + | | [[G40]] || Cancel Cutter Compensation | ||
| + | |- | ||
| + | | [[G41]] [[G42]] || Cutter Compensation | ||
| + | |- | ||
| + | | [[G41.1]] [[G42.1]] || Dynamic Cutter Compensation | ||
| + | |- | ||
| + | | [[G43]] || Use Tool Length Offset from Tool Table | ||
| + | |- | ||
| + | | [[G43.1]] || Dynamic Tool Length Offset | ||
| + | |- | ||
| + | | [[G49]] || Cancel Tool Length Offset | ||
| + | |- | ||
| + | | [[G53]] || Motion in Machine Coordinate System | ||
| + | |- | ||
| + | | [[G54]] - [[G59]] || Select Coordinate System (1 - 6) | ||
| + | |- | ||
| + | | [[G59.1]] - [[G59.3]] || Select Coordinate System (7 - 9) | ||
| + | |- | ||
| + | | [[G61]] [[G61.1]] || Path Control Mode | ||
| + | |- | ||
| + | | [[G64]] || Path Control Mode with Optional Tolerance | ||
| + | |- | ||
| + | | [[G73]] || Drilling Cycle with Chip Breaking | ||
| + | |- | ||
| + | | [[G76]] || Multi-pass Threading Cycle (Lathe) | ||
| + | |- | ||
| + | | [[G80]] || Cancel Motion Modes | ||
| + | |- | ||
| + | | [[G81]] || Drilling Cycle | ||
| + | |- | ||
| + | | [[G82]] || Drilling Cycle with Dwell | ||
| + | |- | ||
| + | | [[G83]] || Drilling Cycle with Peck | ||
| + | |- | ||
| + | | [[G85]] || Boring Cycle, No Dwell, Feed Out | ||
| + | |- | ||
| + | | [[G86]] || Boring Cycle, Stop, Rapid Out | ||
| + | |- | ||
| + | | [[G89]] || Boring Cycle, Dwell, Feed Out | ||
| + | |- | ||
| + | | [[G90]] [[G91]] || Distance Mode | ||
| + | |- | ||
| + | | [[G90.1]] [[G91.1]] || Arc Distance Mode | ||
| + | |- | ||
| + | | [[G92]] || Coordinate System Offset | ||
| + | |- | ||
| + | | [[G92.1]] [[G92.2]] || Cancel Coordinate System Offsets | ||
| + | |- | ||
| + | | [[G92.3]] || Restore Axis Offsets | ||
| + | |- | ||
| + | | [[G93]] [[G94]] [[G95]] || Feed Modes | ||
| + | |- | ||
| + | | [[G96]] || Constant Surface Speed | ||
| + | |- | ||
| + | | [[G97]] || RPM Mode | ||
| + | |- | ||
| + | | [[G98]] [[G99]] || Canned Cycle Z Retract Mode | ||
| + | |} | ||
Revision as of 07:38, January 30, 2014
| Header text | Header text |
|---|---|
| G0 | Coordinated Straight Motion Rapid Rate |
| G1 | Coordinated Straight Motion Feed Rate |
| G2 G3 | Coordinated Helical Motion Feed Rate |
| G4 | Dwell |
| G5.1 | Quadratic B-Spline |
| G5.2 G5.3 | NURBs Block |
| G7 | Diameter Mode (lathe) |
| G8 | Radius Mode (lathe) |
| G10 L1 | Set Tool Table Entry |
| G10 L10 | Set Tool Table, Calculated, Workpiece |
| G10 L11 | Set Tool Table, Calculated, Fixture |
| G10 L2 | Coordinate System Origin Setting |
| G10 L20 | Coordinate System Origin Setting Calculated |
| G17 - G19.1 | Plane Select |
| G20 G21 | Units of Measure |
| G28 - G28.1 | Go to Predefined Position |
| G30 - G30.1 | Go to Predefined Position |
| G33 | Spindle Synchronized Motion |
| G33.1 | Rigid Tapping |
| G38.2 - G38.5 | Probing |
| G40 | Cancel Cutter Compensation |
| G41 G42 | Cutter Compensation |
| G41.1 G42.1 | Dynamic Cutter Compensation |
| G43 | Use Tool Length Offset from Tool Table |
| G43.1 | Dynamic Tool Length Offset |
| G49 | Cancel Tool Length Offset |
| G53 | Motion in Machine Coordinate System |
| G54 - G59 | Select Coordinate System (1 - 6) |
| G59.1 - G59.3 | Select Coordinate System (7 - 9) |
| G61 G61.1 | Path Control Mode |
| G64 | Path Control Mode with Optional Tolerance |
| G73 | Drilling Cycle with Chip Breaking |
| G76 | Multi-pass Threading Cycle (Lathe) |
| G80 | Cancel Motion Modes |
| G81 | Drilling Cycle |
| G82 | Drilling Cycle with Dwell |
| G83 | Drilling Cycle with Peck |
| G85 | Boring Cycle, No Dwell, Feed Out |
| G86 | Boring Cycle, Stop, Rapid Out |
| G89 | Boring Cycle, Dwell, Feed Out |
| G90 G91 | Distance Mode |
| G90.1 G91.1 | Arc Distance Mode |
| G92 | Coordinate System Offset |
| G92.1 G92.2 | Cancel Coordinate System Offsets |
| G92.3 | Restore Axis Offsets |
| G93 G94 G95 | Feed Modes |
| G96 | Constant Surface Speed |
| G97 | RPM Mode |
| G98 G99 | Canned Cycle Z Retract Mode |