Difference between revisions of "DIY CNC Controller"
From CNC.xyz Wiki
(→Bill of Materials (BOM)) |
(→Bill of Materials (BOM)) |
||
| Line 22: | Line 22: | ||
==Bill of Materials (BOM)== | ==Bill of Materials (BOM)== | ||
| − | + | =====3 Axis Kit===== | |
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
| Line 55: | Line 55: | ||
| 14 || 3 || SW1, SW2, SW3 || [http://www.digikey.com/short/j2vrz CT2083-ND] || 3 Position DIP Switch | | 14 || 3 || SW1, SW2, SW3 || [http://www.digikey.com/short/j2vrz CT2083-ND] || 3 Position DIP Switch | ||
|} | |} | ||
| + | |||
| + | =====4 Axis Kit===== | ||
| + | For the 4 axis kit, you will take the above components and add the following components: | ||
| + | |||
| + | TABLE | ||
==Eagle Files== | ==Eagle Files== | ||
Revision as of 05:11, January 29, 2014
 3 Axis Controller | |
| Status | In Production |
|---|---|
| Manufacterer | A Quick CNC |
| Version | 1.0.3 |
More here.
Assembly Instructions
Contents
Schematic
Bill of Materials (BOM)
3 Axis Kit
| Line # | Quantity | Part Code | Digikey | Description |
|---|---|---|---|---|
| 1 | 3 | IC1, IC2, IC3 | SLA7078MPR-ND | SLA7078MPR Driver chip from Sanken |
| 2 | 2 | IC4, IC5 | LM317HVT | High Voltage Adjustable Regulator |
| 3 | 1 | X1 | HRP26H-ND | 26 Pin Male IDC Connector |
| 4 | 4 | TB1, TB2, TB3, TB4 | ED2613-ND | 6 Position Terminal Block |
| 5 | 2 | TB5, TB6 | ED2609-ND | 2 Position Terminal Block |
| 6 | 8 | C1, C2, C3, C4, C5, C6, C7, C11 | 478-3192-ND | Ceramic Capacitor 0.1uF |
| 7 | 3 | C8, C9, C10 | 565-1613-ND | Capacitor Aluminum 680uF 50V 20% |
| 8 | 3 | R1, R2, R3 | CF14JT10K0CT-ND | 10 Kohm 1/4 Watt Resistor |
| 9 | 2 | R5, R7 | CF14JT240RCT-ND | 240 Ohm 1/4 Watt Resistor |
| 10 | 1 | R4 | 715XBK-ND | 715 Ohm 1/4 Watt Resistor |
| 11 | 1 | R6 | 2.05KXBK-ND | 2.05 Kohm 1/4 Watt Resistor |
| 12 | 4 | RN1, RN2, RN3, RN4 | 4606X-1-103LF-ND | 10 Kohm 6-SIP Resistor Network |
| 13 | 3 | VR1, VR2, VR3 | CT6EP102-ND | 1K Variable Trimmer Potentiometer |
| 14 | 3 | SW1, SW2, SW3 | CT2083-ND | 3 Position DIP Switch |
4 Axis Kit
For the 4 axis kit, you will take the above components and add the following components:
TABLE