Difference between revisions of "Grbl Breakout Board"
From CNC.xyz Wiki
(→Bill of Materials (BOM)) |
|||
| Line 39: | Line 39: | ||
! Line # !! Quantity !! Part Code !! Digikey !! Description | ! Line # !! Quantity !! Part Code !! Digikey !! Description | ||
|- | |- | ||
| − | | 1 || 1 || X1 || || IDC26 Ribbon Cable Connector | + | | 1 || 1 || X1 || [http://www.digikey.com/short/pjh70 ED10526-ND] || IDC26 Ribbon Cable Connector |
|- | |- | ||
| 2 || 1 || X2 || [http://www.digikey.com/short/j2vhn ED2613-ND] || 6 Position Terminal Block | | 2 || 1 || X2 || [http://www.digikey.com/short/j2vhn ED2613-ND] || 6 Position Terminal Block | ||
| Line 45: | Line 45: | ||
| 3 || 1 || X3 || [http://www.digikey.com/short/j2vhr ED2609-ND] || 2 Position Terminal Block | | 3 || 1 || X3 || [http://www.digikey.com/short/j2vhr ED2609-ND] || 2 Position Terminal Block | ||
|- | |- | ||
| − | | 4 || 4 || RESET, START, PAUSE, ABORT || | + | | 4 || 4 || RESET, START, PAUSE, ABORT || [http://www.digikey.com/short/pjhjh 679-2428-ND] || Touch Switch |
|- | |- | ||
| 5 || 1 || RN1 || [http://www.digikey.com/short/j2vr2 4606X-1-103LF-ND] || 10 Kohm 6-SIP Resistor Network | | 5 || 1 || RN1 || [http://www.digikey.com/short/j2vr2 4606X-1-103LF-ND] || 10 Kohm 6-SIP Resistor Network | ||
|- | |- | ||
| − | | 6 || 4 || X-AXIS, Y-AXIS, Z-AXIS, A-AXIS || | + | | 6 || 4 || X-AXIS, Y-AXIS, Z-AXIS, A-AXIS || [http://www.digikey.com/short/pjm1v 455-1706-ND] || JST Connector |
|- | |- | ||
| 7 || 1 || A-ENABLE || || Jumper 2x2 | | 7 || 1 || A-ENABLE || || Jumper 2x2 | ||
Revision as of 18:48, February 4, 2014
| Status | In Development |
|---|---|
| Manufacterer | A Quick CNC |
| Version | 1.0.0 |
| Designer | AJ Quick |
| License | CC BY-SA 3.0 |
Contents
Features
- Easily connect up to four Unipolar Motor Driver boards to one Arduino running Grbl.
- Standard port configuration for Grbl running on an Arduino UNO.
- Optional 4th Axis enable through jumpers (requires change to configuration file).
- IDC26 connector to connect directly with DIY CNC Controller.
- Four onboard buttons for Start, Feed Hold (Pause), Abort and Reset.
- Screw terminals for connecting limit switches and E-stop, as well as Coolant enable and Spindle control. (Spindle control not available when using 4th axis).
Board Layout
The board is the same size as an Arduino UNO (or similar board).
Schematic
Bill of Materials (BOM)
| Line # | Quantity | Part Code | Digikey | Description |
|---|---|---|---|---|
| 1 | 1 | X1 | ED10526-ND | IDC26 Ribbon Cable Connector |
| 2 | 1 | X2 | ED2613-ND | 6 Position Terminal Block |
| 3 | 1 | X3 | ED2609-ND | 2 Position Terminal Block |
| 4 | 4 | RESET, START, PAUSE, ABORT | 679-2428-ND | Touch Switch |
| 5 | 1 | RN1 | 4606X-1-103LF-ND | 10 Kohm 6-SIP Resistor Network |
| 6 | 4 | X-AXIS, Y-AXIS, Z-AXIS, A-AXIS | 455-1706-ND | JST Connector |
| 7 | 1 | A-ENABLE | Jumper 2x2 | |
| 8 | 1 | EN/+5V | Jumper 1x3 |
Gerber Files
Gerber files are a universal file type that are commonly used by PCB board manufacturers. These files can be sent directly to a PCB manufacturer to have boards produced.
Eagle Files
Eagle is a very popular PCB design tool created by CadSoft, free and hobbyist licenses are available in addition to professional and commercial licenses.
License
This work is licensed under a Creative Commons Attribution-ShareAlike 3.0 Unported License.