Difference between revisions of "Grbl Breakout Board"
From CNC.xyz Wiki
(→Schematic) |
(→Bill of Materials (BOM)) |
||
| Line 35: | Line 35: | ||
==Bill of Materials (BOM)== | ==Bill of Materials (BOM)== | ||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | ! Line # !! Quantity !! Part Code !! Digikey !! Description | ||
| + | |- | ||
| + | | 1 || 1 || X1 || || IDC26 Ribbon Cable Connector | ||
| + | |- | ||
| + | | 2 || 1 || X2 || [http://www.digikey.com/short/j2vhn ED2613-ND] || 6 Position Terminal Block | ||
| + | |- | ||
| + | | 3 || 1 || X3 || [http://www.digikey.com/short/j2vhr ED2609-ND] || 2 Position Terminal Block | ||
| + | |- | ||
| + | | 4 || 4 || RESET, START, PAUSE, ABORT || || Touch Switch | ||
| + | |- | ||
| + | | 5 || 1 || RN1 || [http://www.digikey.com/short/j2vr2 4606X-1-103LF-ND] || 10 Kohm 6-SIP Resistor Network | ||
| + | |- | ||
| + | | 6 || 4 || X-AXIS, Y-AXIS, Z-AXIS, A-AXIS || || JST Connector | ||
| + | |- | ||
| + | | 7 || 1 || A-ENABLE || || Jumper 2x2 | ||
| + | |- | ||
| + | | 8 || 1 || EN/+5V || || Jumper 1x3 | ||
| + | |} | ||
==Eagle Files== | ==Eagle Files== | ||
Revision as of 07:16, February 4, 2014
| Status | In Development |
|---|---|
| Manufacterer | A Quick CNC |
| Version | 1.0.0 |
| Designer | AJ Quick |
| License | CC BY-SA 3.0 |
Contents
Features
- Easily connect up to four Unipolar Motor Driver boards to one Arduino running Grbl.
- Standard port configuration for Grbl running on an Arduino UNO.
- Optional 4th Axis enable through jumpers (requires change to configuration file).
- IDC26 connector to connect directly with DIY CNC Controller.
- Four onboard buttons for Start, Feed Hold (Pause), Abort and Reset.
- Screw terminals for connecting limit switches and E-stop, as well as Coolant enable and Spindle control. (Spindle control not available when using 4th axis).
Board Layout
The board is the same size as an Arduino UNO (or similar board).
Schematic
Bill of Materials (BOM)
| Line # | Quantity | Part Code | Digikey | Description |
|---|---|---|---|---|
| 1 | 1 | X1 | IDC26 Ribbon Cable Connector | |
| 2 | 1 | X2 | ED2613-ND | 6 Position Terminal Block |
| 3 | 1 | X3 | ED2609-ND | 2 Position Terminal Block |
| 4 | 4 | RESET, START, PAUSE, ABORT | Touch Switch | |
| 5 | 1 | RN1 | 4606X-1-103LF-ND | 10 Kohm 6-SIP Resistor Network |
| 6 | 4 | X-AXIS, Y-AXIS, Z-AXIS, A-AXIS | JST Connector | |
| 7 | 1 | A-ENABLE | Jumper 2x2 | |
| 8 | 1 | EN/+5V | Jumper 1x3 |
Eagle Files
Gerber Files
License
This work is licensed under a Creative Commons Attribution-ShareAlike 3.0 Unported License.