AJ Quick at 01:04, February 13, 2019

2019-02-13T01:04:18Z

AJ Quick: Created page with " This 8-bit non-inverting translator uses two separate configurable power-supply rails. The A port tracks the VCCA pin supply voltage. The VCCA pin accepts any supp..."

2019-02-13T01:01:12Z

Created page with "<amazon /> This 8-bit non-inverting translator uses two separate configurable power-supply rails. The A port tracks the VCCA pin supply voltage. The VCCA pin accepts any supp..."

New page

<amazon />

This 8-bit non-inverting translator uses two separate configurable power-supply rails. The A port tracks the VCCA pin supply voltage. The VCCA pin accepts any supply voltage between 1.2 V and 3.6 V. The B port tracks the VCCB pin supply voltage. The VCCB pin accepts any supply voltage between 1.65 V and 5.5V. Two input supply pins allows for low Voltage bidirectional translation between any of the 1.2 V, 1.8V, 2.5 V, 3.3 V, and 5 V voltage nodes.

When the output-enable (OE) input is low, all outputs are placed in the high-impedance (Hi-Z) state. To ensure the Hi-Z state during power-up or powerdown periods, tie OE to GND through a pull-down resistor. The minimum value of the resistor is determined by the current-sourcing capability of the driver.

Datasheet: http://www.ti.com/lit/ds/symlink/txs0108e.pdf

← Older revision		Revision as of 01:04, February 13, 2019
Line 4:		Line 4:

	When the output-enable (OE) input is low, all outputs are placed in the high-impedance (Hi-Z) state. To ensure the Hi-Z state during power-up or powerdown periods, tie OE to GND through a pull-down resistor. The minimum value of the resistor is determined by the current-sourcing capability of the driver.		When the output-enable (OE) input is low, all outputs are placed in the high-impedance (Hi-Z) state. To ensure the Hi-Z state during power-up or powerdown periods, tie OE to GND through a pull-down resistor. The minimum value of the resistor is determined by the current-sourcing capability of the driver.
		+
		+	'''Key Features'''
		+
		+	*No Direction-Control Signal Needed
		+	*Maximum Data Rates
		+	**110 Mbps (Push Pull)
		+	**1.2 Mbps (Open Drain)
		+	*1.2 V to 3.6 V on A Port and 1.65 V to 5.5 V on B Port (VCCA ≤ VCCB)
		+	*No Power-Supply Sequencing Required – Either VCCA or VCCB Can Be Ramped First
		+	*Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
		+	*ESD Protection Exceeds JESD 22 (A Port)
		+	**2000 V Human Body Model (A114-B)
		+	**150 V Machine Model (A115-A)
		+	**1000 V Charged-Device Model (C101)
		+	*IEC 61000-4-2 ESD (B Port)
		+	**±8 kV Contact Discharge
		+	**±6 kV Air-Gap Discharge

	Datasheet: http://www.ti.com/lit/ds/symlink/txs0108e.pdf		Datasheet: http://www.ti.com/lit/ds/symlink/txs0108e.pdf

TXS0108E - Revision history

AJ Quick at 01:04, February 13, 2019

AJ Quick: Created page with " This 8-bit non-inverting translator uses two separate configurable power-supply rails. The A port tracks the VCCA pin supply voltage. The VCCA pin accepts any supp..."