G01 - Revision history

AJ Quick at 05:41, February 3, 2014

2014-02-03T05:41:06Z

2014-01-31T06:44:28Z

‎Code Examples

2014-01-31T06:42:35Z

‎Code Examples

2014-01-31T06:41:52Z

‎Code Examples

2014-01-31T06:39:47Z

2014-01-31T01:15:18Z

2014-01-30T21:11:18Z

2014-01-30T21:11:12Z

2014-01-30T21:10:52Z

2014-01-30T21:02:48Z

@@ Line 4: / Line 4: @@
   G1 X0.000 Y0.000 Z0.000 F100.0
-Where the numbers following the X, Y, Z and F can be changed for the designed amount. Additional commands can also be added for a 4-Axis or larger machine.
+Where the numbers following the X, Y, Z and F can be changed for the desired amount. Additional commands can also be added for a 4-Axis or larger machine.
 ==Code Examples==

@@ Line 21: / Line 21: @@
   G1 X-1.000 Y-1.000 Z-1.000
-As a final example we will take a system that is setup to run in inches, move to an absolute position of (1,1,1) convert to mm, move one millimeter to the side and then convert back to inches. The final position will be (1 mm, 1 inch, 1 inch). The change of units is done with [[G20]] and [[G21]], and an a M-code ([[M02]]) indicates the end of the cycle.
+As a final example we will take a system that is setup to run in inches, move to an absolute position of (1,1,1) convert to mm, move one millimeter from the origin and then convert back to inches. The final position will be (1 mm, 1 inch, 1 inch). The change of units is done with [[G20]] and [[G21]], and an a M-code ([[M02]]) indicates the end of the cycle.
   G20

@@ Line 19: / Line 19: @@
   G1 X0.000 Y0.000 Z0.000 F100.0
-  G1 X1.000 Y1.000 Z1.000
+  G1 X-1.000 Y-1.000 Z-1.000
 As a final example we will take a system that is setup to run in inches, move to an absolute position of (1,1,1) convert to mm, move one millimeter to the side and then convert back to inches. The final position will be (1 mm, 1 inch, 1 inch). The change of units is done with [[G20]] and [[G21]], and an a M-code ([[M02]]) indicates the end of the cycle.

@@ Line 11: / Line 11: @@
   G1 X1.000 Y1.000 Z0.000 F100.0
-This example will raise the height of the Z-Axis 1 unit higher at the current federate. Notice that units that are not changed, do not have to be entered.
+This example will raise the height of the Z-Axis from the origin to be 1 unit higher at the current federate. Notice that units that are not changed, do not have to be entered.
   G1 Z0.000 F100.0

@@ Line 7: / Line 7: @@
 ==Code Examples==
-In this example, the machine will move from its current position to a position (1,1,0) units away at a federate of 100 units per minute. (The units can be set using [[G20]] and [[G21]].)
+In this example, the machine will move from its current position to an absolute position of (1,1,0) units at a federate of 100 units per minute. (The units can be set using [[G20]] and [[G21]].)
   G1 X0.000 Y0.000 Z0.000 F100.0
   G1 X1.000 Y1.000 Z0.000 F100.0

← Older revision		Revision as of 01:15, January 31, 2014
Line 1:		Line 1:
−	The '''Linear Interpolation''' G-code, known as G01 allows the machine to move with exact synchronization of all its axis. The machine will move relative to the absolute position set initially or through offsets.	+	The '''Linear Interpolation''' G-code, known as G01 allows the machine to move with exact synchronization of all its axis. The machine will move relative to the absolute position set initially or through offsets. The G01 G-code can also be written as G1, and most CNC programs can accept either G01 or G1. We use G1 in our examples to save space, which is important when using software such as [[Grbl]].

	'''Standard Format:'''		'''Standard Format:'''

@@ Line 16: / Line 16: @@
 This example shows that negative movements are also possible. We will move to a relative position of (1,1,1) and then back (-1,-1,-1) to arrive back at the original position.
-  G1 X1.000 Y1.000 Z1.000<br />
+  G1 X1.000 Y1.000 Z1.000
   G1 X-1.000 Y-1.000 Z-1.000
 As a final example we will take a system that is setup to run in inches, move to an absolute position of (1,1,1) convert to mm, move one millimeter to the side and then convert back to inches. The final position will be (1.039, 1, 1). There is a mix of [[G00]] (absolute positioning), a change of units with [[G20]] and [[G21]], as well as a M-code ([[M02]]) which indicates the end of the cycle.
-  G20<br />
+  G20
-  G0 X0.000 Y0.000 Z0.000 F100<br />
+  G0 X0.000 Y0.000 Z0.000 F100
-  G1 X1.000 Y1.000 Z1.000 F100<br />
+  G1 X1.000 Y1.000 Z1.000 F100
-  G21<br />
+  G21
-  G1 X1.000<br />
+  G1 X1.000
-  G20<br />
+  G20
   M2
 [[Category: G-code]]